|
|
|
800-876-0036
Phone: 847-356-0566 Fax: 847-356-0747 E-Mail: sales@mmcontrol.com
|
Titan Check Valves: Check valves prevent the system from draining if the pump stops and protect against backflow, which could harm the pump or other equipment.Titan Flow Control, Inc. offers a variety of check valve designs to meet your specific needs including center-guided globe style valves, center-guided wafer style valves, center guided threaded valves, dual disc check valves, single disc check valves, and full body swing check valves. |
Center-Guided Check Valves
Globe Style
Center Guided Silent Globe Type
MODELS:
CV 50 - DI Globe Class 150 Ductile Iron Sizes 2" - 24"
CV 51 - CS/SS Globe Class 150 Carbon or Stainless Sizes 2" - 24"
CV 52 - DI Globe Class 300 Ductile Iron Sizes 2" - 24"
CV 52 - CS/SS Globe Class 300 Stainless Steel Sizes 2" - 14"
Size Range: 2" - 24"
Larger Sizes Available
Titan Engineers developed the patented CV 50 series of center guided, globe style, check valves. Only Titan's CV 50 series have integral straightening vanes to calm turbulent flows, smaller stem guides for less flow obstruction, and extra clearance to allow direct butterfly valve installation on the outlet side.
Wafer Style
Wafer Type Silent Check Valve
MODELS:
CV 90 - DI Wafer Class 150 / 300 Ductile Iron Sizes 2" - 12"
CV 91 - SS Wafer Class 150 / 300 Stainless Steel Sizes 2" - 12"
Size Range: 2" - 12"
Sizes 2" - 6" Provide Dual Pressure Service ASME Class 150/300
Designed for Long Service Life
Newly designed CV90's have straightening vanes that reduce turbulence in incoming flow, thus minimizing noise, vibrations, erosion, cavitations, and other factors that could result in premature valve failure.
Threaded End Silent
Threaded End Silent Check Valve
MODELS:
CV 20 - BR Threaded
WOG 400 PSI @ 100°F
Brass Sizes 1/4" - 2"
CV 80 - SS Threaded Class 300
WOG 720 PSI @ 100°F
Stainless Steel Sizes 3/8" - 3"
Size Range: 1/4" - 3"
Quick Closure to Reduce Water Hammer
Silent shut-off is achieved via the fully automatic, spring assisted disc that closes near zero flow velocity. The lightweight, center guided disc design creates a positive shutoff prior to flow reversal and helps to keep slamming and surges to a minimum.
Wafer Type Axial Flow
Center Guided Wafer Type Axial Flow
MODELS:
CV 92 - CS Wafer Class 150 Carbon Steel Sizes 2" - 24"
Non-Slam
CV 92 - SS Wafer Class 150 Stainless Steel Sizes 2" - 24"
Non-Slam
Non-return non-slam check valve designed for low flow fluctuating systems and for critical applications where backflow is a concern. The diffuser prevents backflows from impacting the back side the discs.
Insert Check Valve
Center Guided Wafer Type Insert Check Valve
MODEL:
CV 71 - SS Wafer Class 150 / 300 Stainless Steel Sizes 1/2" - 6"
Silent shut-off is achieved via the fully automatic, spring assisted disc that closes near zero flow velocity. The lightweight, center-guided disc design creates a positive shutoff prior to flow reversal and helps to keep slamming and surges to a minimum.
|
|
Wafer Type
Complies with API 594 Dimensions
The CV41A-DI meets API 594 ASME Class 125 face-to-face dimensions, This allows the CV41A-DI to be a natural replacement for outdated cast iron valves while achieving the superior material benefits of ductile iron.
Check Valves
Dual Disc
ASME 150, 300, 600, 900
Carbon and Stainless Steel
MODELS:
CV 41 - DI Wafer Class 150 Ductile Iron Sizes 2" - 24"
CV 41A - DI Wafer Class 150 Ductile Iron Sizes 2" - 24"
CV 42 - CS/SS Wafer Class 150 Carbon or Stainles,s Sizes 2" - 24"
CV 44 - CS/SS Wafer Class 300 Carbon or Stainless, Sizes 2" - 24"
CV 46 - CC/SS Wafer Class 600 Carbon or Stainless, Sizes 2" - 24"
CV 47 - CC/SS Wafer Class 900 Carbon or Stainless, Sizes 2" - 24"
SIZE RANGE: 2" - 24"
Larger Sizes Available
Wafer CV, Lug Type
Minimal Head Loss
Contour of body provides a short and straight flow path that generates very little turbulence. Additionally, the spring-loaded discs are designed with very low cracking pressure which reduces the amount of energy required to open the valve.
Check Valve Wafer Type
Lug Style
ASME Class 150
Carbon and Stainless Steel
MODELS:
CV 42L - CS/SS Lug Class 150 Carbon or Stainless, Sizes 2" - 24"
SIZE RANGE: 2" - 24"
Lug Styles are Blind Tapped as Standard
2" - 5" Have Retainer-Ring Design.
6" - 24" Use Retainer-Cap Design.
Fugitive Emission Design
The retainer-less body design eliminates potential leak paths to the environment so there are no body emissions.
|
|
Check Valve Single Disc
Threaded & Socket Weld
Single Disc SS Check Valve
Check Valve, Stainless Steel, ASME Class 300, Threaded, Socket Weld
MODELS:
CV 88T - SS
Stainless Steel - Threaded
Sizes 1/2" - 3"
CV 88S - SS
Stainless Steel Socket Weld
Sizes 1/2" - 3"
Size Range: 1/2" - 3"
Simple Design
The all stainless-steel body coupled with a simplified design (only three parts) helps to eliminate possible failure points. The need for O-rings or gasket seals is not needed.
Swing Check Valve
Short Wafer Type
Single Disc Short Pattern Design
MODELS:
CV 12-CS
Body: Carbon Steel
Seat/Seal: Buna-N
Short Wafer Class 150 Carbon Steel Sizes 2" - 24"
CV 12-SS
Body: Stainless Steel
Seat/Seal: PTFE
Short Wafer Class 150 Stainless Steel Sizes 2" - 24"
Size Range: 2" - 24"
Robust Design
This is a self-acting, non-return, single plate, wafer type swing check valve which provides high quality and reliability within a simplified construction.
Check Valve Single Disc
Swing Type Wafer
Single Disc Swing Check Valve
Check Valve, Single Disc Swing Type Wafer Type
MODELS:
CV 31-DI
Body: Ductile Iron
Seat: Buna-N
Disc: Stainless Steel
ASME Class 150 Sizes 2" - 12"
CV 32-CS/SS
Body: Carbon Steel - Seat: Viton
Body: Stainless Steel - Seat: PTFE
Disc: Stainless Steel
ASME Class 150 Sizes 2" - 12"
CV 34-CS/SS
Body: Carbon Steel - Seat: Viton Body: Body: Stainless Steel - Seat: PTFE
Disc: Stainless Steel
ASME Class 300 Sizes 2" - 12"
Size Range: 2" - 12"
(14" - 24" Available)
Swing Check Valve Single Disc Grooved Ends
Single Disc Swing Type, Grooved Ends
Check Valve, Ductile Iron, WOG 300, Single Disc Swing Type, Wafer Type, Grooved End, Fire Protection
MODELS:
CV 31G-UL-DI
Ductile Iron - ASTM A536
Sizes 2" - 12"
Titan unit CV31G-UL grooved end design can be quickly and easily installed with industry standard AWWA C606 couplings.
|
Swing Check w/ Weight & Lever
Model
CV31WF-CI
Proven Design
The full body swing check is one of the most well-known types of check valves. It is ideal for preventing flow reversal which aids in protecting compressors, pumps, and downstream tanks and vessels.
Full Body Swing Check
Valve - Flanged Ends
Single Disc
ASME 125
Cast Iron Body
MODEL:
CV 31WF-CI
Body: Cast Iron
Body Seat: Bronze
Disc: Cast Iron
Disc Seat: Buna-N
Weight & Lever : Cast Iron
SIZE RANGE: 2" - 12"
Full Body Swing Check
Model
CV31F-CI
Proven Design
The full body swing check is ideal for preventing flow reversal which aids in protecting compressors, pumps, and downstream tanks and vessels. The Titan CV31F can also be used to isolate high pressure systems from low pressure systems and to prevent contamination between systems.
Full Body Swing Check
Valve - Flanged Ends
Single Disc
ASME 125
Cast Iron Body
MODEL:
CV 31F-CI
Body: Cast Iron
Body Seat: Bronze
Disc: Cast Iron
Disc Seat: Buna-N
SIZE RANGE: 2" - 12"
|
|
| Can't find what you are looking for?
Call or E-mail Now
. . . for Immediate Service, Pricing, and Delivery |
|
* * * 800-876-0036 * * *
Phone: 847-356-0566 Fax: 847-356-0747 E-Mail: sales@mmcontrol.com
@
|
