Hedland Turbine (Water) Technology & Electronic Readouts and Accessories

800-876-0036

Phone: 847-356-0566 Fax: 847-356-0747 E-Mail

HEDLAND Turbine Flow Meters (Water/Water-Based Fluids)

Turbine Meters

Benefits & Features

Flow ranges: 0.6 - 3.0 GPM (2.27 - 11.36 LPM)
up to 500 - 5000 GPM (1893 - 18927 LPM)
Rugged contruction
- Body: T316 Stainless steel
- Rotor: T416 Stainless steel
- Internal supports: Tungsten carbide
- Bearings: Tungsten carbide journals
- Retaining rings: T303 Stainless steel
- Pick-up: Magnetic, Standard
Meter bore sizes from 3/8 to 10 inch
Ports:
- 1/2 to 2 inch NPT
- 3 to 10 inch Victaulic® grooved ends
Pressure: 5,000 psi (345 bar) maximum
Temperature:
- Standard: 330° F (165° C) maximum
- High Temp: 450° F (232° C) maximum
Accuracy within ±1% of reading
Standard calibration: 1.0 specific gravity for water and water-based liquids
Magnetic pick-up output: 30 millivolts to 3 volts – peak-to-peak

Electronic Readouts

Benefits & Features

The Hedland Model HB2800 is a state-of-the-art flow monitor designed to be utilized with all Hedland HB Series turbine flow sensors. The HB2800 comes pre-calibrated by the factory when ordered with a Hedland HB Series turbine flow sensor, or the monitor may be configured in the field. The HB2800 may also be used with almost any flow sensor that outputs a low-amplitude AC signal.

Features include:

Microprocessor-based
Battery (1.5 VDC) or loop-powered (4-20 mA) versions
Extra large rate and total display
Meter, remote, panel, or swivel mount options
NEMA 4X/CSA Type 4 enclosure
Intrinsically safe
Explosion-proof model available

Electronic Accessories

Spec & Tech Sheets

Hedland F Converters and K Factor Scalers

Benefits & Features

F-I Analog Transmitter
- Converts frequency outputs to 4–20 mA output
- Cannister or condulet models available
- 2-wire loop powered
F-V Analog Voltage Transmitter
- Converts frequency outputs to 0–5 Vdc output
- Cannister or condulet models available
- Requires 10-30 Vdc power supply
K-factor Scaler
- Scales turbine meter output to esired engineering unit
- Amplifies turbine meter pulse output
- Converts frequency outputs into recognizable units for PLCs and other devices
- NEMA 4X enclosure
- Requires 8.5–30 Vdc power supply
Cables
- Standard 10 foot cables
- Variety of connectors

Can't find what you are looking for?

Call or E-mail Now . . . for Immediate Service, Pricing, and Delivery

* * * 800-876-0036 * * *

Phone: 847-356-0566 Fax: 847-356-0747 Request Quote

WARNING: Some of the products we sell can expose you to chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Contact your sales rep or go to www.P65Warnings.ca.gov for more information.

All registered trademarks are fully acknowledged by: M&M Control Service, Inc.

M&M Control Service, Inc. does not represent or claim any affiliation, association, connection or approvals with or from any manufacturer unless stated. We fully acknowledge all trademarks and/or names which are pictured and/or listed throughout the M&M Control Service, Inc. Website.

(Powers^TM, also known as, POWERS REGULATOR, MCC POWERS, POWERS-FIAT, POWERS PROCESS CONTROLS, CRANE POWERS and POWERS, a Watts Industries Company. The POWERS trademark is owned by Powers, A Division of Watts Water Technologies, Inc. M&M Control Service, Inc. Is a Stocking Distributor for Powers^TM)

(All names unintentionally excluded from this list will be included in the next revision upon our notification.)

*This list may vary, as names not appearing on this list are entitled to the acknowledgment of their Trademarks by M&M Control Service, Inc.